Renovation Field Guide

Guides

Grout and tile adhesive explained

Grout fills joints. Adhesive holds tile. Neither keeps water out of a wall, and knowing what does is the difference between a bathroom that lasts and one that rots quietly.

6 min read · Updated 2026-11-21

A plainly tiled wall in low afternoon sun, the grout joints picked out by the raking light.

The three layers, and which one matters

In a tiled wet area there are three things doing three jobs, and people routinely confuse them.

The waterproofing layer sits behind everything and is the only thing stopping water reaching the structure. It is a membrane or a liquid-applied system, installed to a national standard, usually a condition of home insurance and usually requiring a documented guarantee. In a shower or wet room this is the part of the job that matters.

The adhesive bonds tile to substrate. Its other job, less obvious, is to make up the difference between a perfectly flat tile and a wall that is not.

The grout fills the joints between tiles. It stops edges chipping, keeps dirt out of the gaps, and lets the surface move very slightly without cracking. It is not a seal.

If you take one thing from this page: water gets through grout, and always has. A bathroom that fails rarely fails at the tile. It fails behind it, slowly, and the first sign is often a stain on a ceiling below.

How much grout

Grout fills joint volume, so the driver is joint length per square metre — and that is governed by tile size, not by area.

The standard formula:

grout in kg/m² = ((A + B) ÷ (A × B)) × C × D × ρ

A and B are the tile's dimensions in millimetres, C is the joint width, D is the joint depth (use the tile thickness), and ρ is the grout's density in kg/dm³ — usually around 1.6, sometimes 1.5 or 1.8. It is on the bag.

The effect of tile size is dramatic:

Tile Joint Grout
100 × 100 mm 3 mm wide, 8 mm deep about 0.77 kg/m²
300 × 600 mm 3 mm wide, 9 mm deep about 0.24 kg/m²
600 × 600 mm 2 mm wide, 10 mm deep about 0.11 kg/m²

A mosaic can use seven times the grout of a large-format tile over the same wall. This is also why mosaic takes so much longer to grout.

Buy one bag more than the figure. Part-mixed grout cannot be kept, and running out mid-wall means a visible join where the second batch starts.

How much adhesive

There is no formula, because the answer depends on things a calculator cannot see. The trade ranges:

Tile size Typical adhesive
Small, up to about 250 mm 3–4 kg/m²
Medium, 250–450 mm 4–6 kg/m²
Large format, over 450 mm 6–9 kg/m², often more

Large format needs more for two reasons: a bigger notch trowel, and back-buttering — adhesive applied to the tile as well as the wall, to get the coverage that stops a tile sounding hollow and cracking later.

If your substrate is out of true, assume the top of the range. Adhesive is the cheapest way to make up a few millimetres, and the most expensive way to make up twenty — at that point the wall needs levelling first.

The decisions worth making before you order

Joint width is not only aesthetic. Narrow joints demand a flat substrate and tile with consistent dimensions. Rectified large-format tile can take 2 mm; handmade or pressed tile cannot, because the tiles themselves vary. Wider joints are more forgiving and give the surface somewhere to move.

Movement joints are not optional. Large tiled areas, changes of plane, internal corners and junctions with other materials need a flexible joint rather than rigid grout. Where they go is a specification question, and getting it wrong shows up as a line of cracked grout along a corner within a year.

Grout colour changes the room more than the tile does. A pale grout with dark tile reads as a grid; matched grout reads as a surface. Pale grout on a floor also shows every mark. Decide before you buy, and buy a little extra of the exact colour.

Some stone stains. Pigmented grout can mark porous natural stone permanently, and the usual answer is to seal the tile before grouting. Check what the tile supplier specifies.

Substrate decides the product. Plasterboard, cement board, concrete, screed, an existing tile surface and a heated floor are all different cases, and adhesives are formulated for them. Over underfloor heating you need a flexible adhesive and grout, because the floor moves as it cycles.

Where this sits in the job

After boarding, after any waterproofing is done and signed off, before final decorating. Grout haze and cut dust ruin fresh paint, which is why tiling comes first.

Give the adhesive its full setting time before grouting, and the grout its full time before the shower is used. Both are printed on the bag, both are longer in a cold room, and both are routinely ignored.

Common questions

Is grout waterproof?
No, and it never has been. Water passes through cement-based grout. What keeps water out of the structure is the waterproofing layer behind the tile, installed to a national standard. Tile and grout are the wearing surface, not the barrier.
How much grout do I need?
It depends far more on tile size than on area, because small tiles have much more joint length per square metre. The standard formula is in the tile calculator: ((A + B) divided by (A times B)) times joint width times joint depth times grout density.
Why does my adhesive quantity vary so much?
Because it fills the gap between a flat tile and a substrate that is not flat. The notch size on the trowel, how true the wall is and whether you back-butter the tile all change it, which is why the figure is a range rather than a number.
Can I use the same grout everywhere?
No. Joint width, movement, chemical exposure and whether the surface stays wet all change what is appropriate, and so does the tile — some stone stains from pigmented grout. Read what the tile maker and the grout maker each specify, and where they disagree, ask.