
How the figures are worked out
Nothing here is a secret formula. If you would rather do it on paper, this is the arithmetic.
Area. Each surface is width × height × how many. All the surfaces are added together, then the openings you listed are subtracted the same way. That gives the net area.
Waste. The net area is multiplied by one plus your waste percentage. This is the figure everything else is based on, because the tiles you cut and break are tiles you still have to buy.
Tiles. One tile covers its width × its height, converted to square metres. The area with waste divided by that, rounded up.
Boxes. Tiles divided by tiles per box, rounded up. Rounding up at the box stage is why the real waste is usually a little higher than the percentage you entered — you cannot buy two-thirds of a box.
Grout. This is the standard trade formula:
grout in kg/m² = ((A + B) ÷ (A × B)) × C × D × 1.6
where A and B are the tile's dimensions in millimetres, C is the joint width, D is the joint depth (take it as the tile's thickness), and 1.6 kg/dm³ is a typical density for cement-based grout. Check the bag — some are 1.5, some 1.8.
Adhesive. There is no formula, because the answer depends on how flat your substrate is and what notch trowel you use. The calculator gives the trade range for your tile size: around 3–4 kg/m² for small tiles, 4–6 for medium, 6–9 for large format where you are also back-buttering. If your wall is out of true, assume the top of the range and then some.
The decisions that change the numbers
Tile size against room size. Large format tile looks calm in a big room and chaotic in a small one, because a small room cannot take a full tile across its width and you end up with a thin sliver at one edge. Before you commit, work out where the cut line falls. Starting from the centre of the most visible wall rather than from a corner usually gives you two equal cuts at the edges instead of one awkward one.
Joint width. It is not only a look. Narrow joints need a flat substrate and a tile with consistent dimensions; rectified large-format tile can take 2 mm, handmade or pressed tile cannot. Wider joints are more forgiving and give the floor somewhere to move.
Layout direction. Running tile the long way makes a room read as longer. Diagonal layouts waste far more and are much harder to cut well. Herringbone is beautiful and is the most expensive thing on this page, in material and in labour.
What this calculator does not cover
Tile in a shower or a wet room sits on top of a waterproofing layer, and that layer is the part that matters. Tile and grout are not waterproof — water passes through grout, and always has. What stops it reaching the structure is the membrane or tanking system behind, installed to a national standard, usually as a condition of your home insurance.
If you are tiling a dry wall or a dry floor, the numbers above are the whole job. If you are tiling anything that gets wet, the numbers above are the cheap part, and the part underneath is the one to get a documented guarantee on.
Common questions
- How much extra tile should I buy?
- Ten to fifteen per cent over the measured area for a straight layout, fifteen to twenty for diagonal, herringbone or chevron. Buy the whole quantity in one order and keep the offcuts — the same batch will not be available in two years, and a replacement from a different batch will not match.
- Do I subtract windows and doors?
- Yes, but only openings big enough to matter. A door at 0.9 by 2.0 metres is 1.8 square metres, which is most of a box. A small window in a wall you are tiling around is usually left in the figure as part of the waste allowance.
- Why does the grout figure change so much with tile size?
- Grout fills the joints, and small tiles have far more joint length per square metre than large ones. A 100 mm mosaic can need eight times the grout of a 600 mm format over the same area.
- Can I tile over existing tile?
- Sometimes, and it depends entirely on whether the existing tile is sound, well bonded and on a substrate that can take the extra weight — plus what it does to door thresholds and fittings. It is a judgement call for someone who can see the wall, not something to decide from a calculator.