How the figures are worked out
This is the decorator's method, not the area method.
Drops needed. Total wall width, less any full-height openings, divided by the roll width, rounded up. Each drop is one strip of paper from ceiling to skirting.
Drop length. Wall height plus 100 mm trim allowance — 50 mm top and bottom, to square up against ceilings and skirtings that are never quite level. Then, if there is a pattern repeat, rounded up to a whole number of repeats, because every drop has to start at the same point in the design.
Drops per roll. Roll length divided by drop length, rounded down. This is the step that matters. You cannot use a partial drop.
Rolls. Drops needed divided by drops per roll, rounded up.
A worked example. A room with 15.6 m of wall, a 0.9 m door to skip, 2.4 m ceilings, a standard 10.05 × 0.53 m roll and no pattern:
- Drops: (15.6 − 0.9) ÷ 0.53 = 27.7, so 28 drops
- Drop length: 2.4 + 0.1 = 2.5 m
- Drops per roll: 10.05 ÷ 2.5 = 4.02, rounded down to 4
- Rolls: 28 ÷ 4 = 7 rolls
Now give that paper a 640 mm repeat. Each drop has to be a whole number of repeats, and 2.5 m needs four of them, so the drop grows to 2.56 m. Drops per roll falls from 4 to 3, and the same room now needs 10 rolls.
Three extra rolls, for a pattern — and note how little it took. The drop only grew by 6 cm, but that was enough to lose a whole drop from every roll. That is not a rounding error in the calculator; it is what patterned paper costs, and it is why a large repeat on a low wall is the most wasteful combination there is.
Buying and ordering
Always one order, always one batch. This is the rule that catches people out. Check the batch or lot number on every roll before you cut anything.
Add a roll if the paper is discontinued or imported. Reordering in three weeks may not be possible at all, and a repair later is impossible without spare.
Keep the offcuts and the label. The label has the batch number, the repeat and the paste type. In five years when a pipe leaks, that label is worth more than the paper.
A note on the wall itself
Paper is less forgiving than paint about what is under it. Old paper has to come off properly, not be papered over. The wall needs filling, sanding and sizing — a thinned coat that stops the plaster drinking the paste and gives you time to slide the paper into place. Fresh plaster needs to be fully dry and sized, or the paper will not come off again in ten years without taking the plaster with it.
If a wall is damp, paper will tell you so within a season. Find out why before you cover it.
Common questions
- Why not just divide the wall area by the roll area?
- Because a drop that is one centimetre short is waste no matter how much paper is left on the roll. If your wall needs a 2.5 metre drop and the roll is 10 metres, you get three drops and 2.5 metres of unusable offcut, not four. Dividing by area gets this wrong in the direction that leaves you short.
- What is a pattern repeat and why does it cost me rolls?
- The distance before the design starts again. Every drop has to begin at the same point in the pattern to line up with its neighbour, so each drop is rounded up to a whole number of repeats. A large repeat on a low wall can waste nearly a full repeat per drop.
- Should I subtract windows and doors?
- Only full-height openings, and only their width. A window in the middle of a wall still needs paper above and below it, from the same drop, so it does not save you a roll — it just gives you offcuts. Leave it in.
- What is a batch number and why does it matter?
- A production run code printed on the label. Colour varies slightly between runs, and the difference shows as a visible band on the wall. Buy every roll in one order and check the numbers match before you open any of them.