Protection first, and not as a formality
This is the part of a tool list that gets skimmed, and it is the part with permanent consequences.
- Safety glasses that fit, worn whenever anything is cut, drilled or struck
- A fitted dust mask, rated for fine particles. Silica dust from cutting masonry, tile, concrete and board is a documented health hazard, and a loose cloth mask does nothing about it
- Ear defenders. Power tools in a bare room are far louder than the same tools outdoors
- Gloves, and sturdy footwear with a toe cap
- A dust extractor or a shop vacuum with a good filter, connected to the tool that is making the dust rather than used afterwards
If the building predates the 1990s, stop before you sand or cut anything unknown. Asbestos in board, textured coatings, floor tiles, adhesive and pipe lagging is harmless undisturbed and dangerous once broken up. Lead paint, in anything before the late 1970s, is the same story. Both need testing, not assumption.
Measuring and marking
- 5 m retractable tape
- Laser distance measure, if you are measuring a whole house
- A spirit level you have checked for accuracy — 600 mm for general work, 1800 mm if you are fitting units or tiling
- Combination square
- Chalk line
- Pencils, and a marker for dark surfaces
- Self-levelling laser: hire or buy, and genuinely transformative for tiling and for fitting a run of units
Demolition and strip-out
- Claw hammer and a wrecking bar
- Utility knife, and more blades than you think
- Scrapers, wide and narrow
- Bolster chisel and a club hammer
- Rubble sacks — many more than you estimate
- SDS rotary hammer: hire. Expensive to buy, used for a day, and the hire machine is better than the one you would buy
Fixing and assembly
- Cordless drill-driver, with a spare battery
- Impact driver, if you are putting in any quantity of screws
- Drill bit set, including masonry bits
- Screwdriver set
- Adjustable spanner and pliers
- Clamps. Always more clamps
Cutting
- Hand saw
- Jigsaw, for curves and cut-outs
- Circular saw or a mitre saw, for anything with a straight repeated cut — skirting, architrave, flooring
- Multi-tool, which is the thing that gets you out of awkward situations: cutting a skirting in place, trimming a door lining, undercutting a frame
- Tile cutter for straight cuts; hire a wet saw for large format, stone or anything with mitres
Surfaces
- Filling knives, in two or three widths
- Sanding block and paper, plus a pole sander for ceilings
- Caulking gun
- Mixing bucket and a paddle for the drill
- Notched trowel, in the size your adhesive specifies
- Grout float and sponges
- Tile spacers and levelling clips, for large format
- Brushes and rollers, and a decent roller frame. Cheap rollers shed fibres into the finish
Hire, do not buy
Floor sanders. Scaffold towers and podium steps. Wet tile saws. SDS breakers. Plate compactors. Mixing stations. Dehumidifiers for drying out a screed. Carpet and floor lifters.
All of these are expensive, bulky, used briefly, and better in hire-grade form than in the consumer version.
Leave to a trade
Not a list of difficult jobs — a list of jobs where the tool is the smallest part of the problem.
Anything inside a consumer unit or breaker panel. Gas. Soldering or pressing pipework that will be buried in a wall. Wet-room waterproofing that needs a documented guarantee. Anything structural. Flue and chimney work.
In every one of those cases the failure mode is fire, flood inside a wall, or carbon monoxide, and in most countries the work is licensed for exactly that reason. Owning the tool does not change that.
Common questions
- Buy or hire?
- Buy what you will use on more than one job and can store. Hire anything large, expensive, used for a day, or awkward to keep — floor sanders, SDS breakers, scaffold towers, tile saws, mixing stations. Hiring also gets you a better machine than you would buy.
- What is the first thing to buy?
- A decent cordless drill-driver, a 5 metre tape, a spirit level you trust, and proper protection — goggles, gloves, a fitted dust mask and ear defenders. The protection is not the boring part of the list; it is the part that has consequences.
- What tool do people most regret skipping?
- A dust extractor or at least a shop vacuum with a decent filter, connected to whatever is making the dust. Construction dust is the thing that makes living through a renovation unbearable, and it is also a genuine health matter with silica and old coatings.
- Do I need a laser level?
- For a single room, a good spirit level is enough. For tiling, fitting a run of units, or anything that must be level across a whole room, a self-levelling laser earns its cost in one job and takes a person out of the equation.
